Hi Faisal, Faisal Islam wrote: > Hello Al, > > Would you please try the following and see what happens? > > 1. Connect your Treo to your computer via USB and turn it on > 2. Open a Shell and log in as root (type in su and the root pwd) > 3. Type in the following and see if visor shows up > lsmod | grep visor > -- if it does, proceed to step 5 > -- if not, proceed to step 4 > I get: AL-WS:/dev # lsmod | grep visor visor 37644 0 usbserial 52688 1 visor usbcore 156456 6 visor,usbserial,usbhid,ehci_hcd,ohci_hcd > 4. Type the following in the shell prompt > modprobe visor > -- you should not get errors > -- go to step 3 above > 5. Type the following in the shell prompt > tail -f /var/log/messages > I get: tail -f /var/log/messages May 7 08:51:08 AL-WS kernel: usb 1-2: new full speed USB device using ohci_hcd and address 105 May 7 08:51:08 AL-WS kernel: usb 1-2: new device found, idVendor=0830, idProduct=0061 May 7 08:51:08 AL-WS kernel: usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=5 May 7 08:51:08 AL-WS kernel: usb 1-2: Product: Palm Handheld May 7 08:51:08 AL-WS kernel: usb 1-2: Manufacturer: Palm, Inc. May 7 08:51:08 AL-WS kernel: usb 1-2: SerialNumber: PalmSN12345678 May 7 08:51:09 AL-WS kernel: usb 1-2: configuration #1 chosen from 1 choice May 7 08:51:09 AL-WS kernel: visor 1-2:1.0: Handspring Visor / Palm OS converter detected May 7 08:51:09 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB0 May 7 08:51:09 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB1 > 6. Press the HotSync button on your Treo and check the output in step 5 > above. This will show you what the computer sees. The following is an > example: > > May 6 07:43:49 localhost kernel: visor 1-1:1.0: Handspring Visor / Palm > OS converter detected > May 6 07:43:49 localhost kernel: usb 1-1: Handspring Visor / Palm OS > converter now attached to ttyUSB0 > May 6 07:43:49 localhost kernel: usb 1-1: Handspring Visor / Palm OS > converter now attached to ttyUSB1 > I get (after a few minutes): May 7 08:53:53 AL-WS kernel: usb 1-2: USB disconnect, address 105 May 7 08:53:53 AL-WS kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0 May 7 08:53:53 AL-WS kernel: visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1 May 7 08:53:53 AL-WS kernel: visor 1-2:1.0: device disconnected May 7 08:53:54 AL-WS kernel: usb 1-2: new full speed USB device using ohci_hcd and address 106 May 7 08:53:54 AL-WS kernel: usb 1-2: new device found, idVendor=0830, idProduct=0061 May 7 08:53:54 AL-WS kernel: usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=5 May 7 08:53:54 AL-WS kernel: usb 1-2: Product: Palm Handheld May 7 08:53:54 AL-WS kernel: usb 1-2: Manufacturer: Palm, Inc. May 7 08:53:54 AL-WS kernel: usb 1-2: SerialNumber: PalmSN12345678 May 7 08:53:54 AL-WS kernel: usb 1-2: configuration #1 chosen from 1 choice May 7 08:53:54 AL-WS kernel: visor 1-2:1.0: Handspring Visor / Palm OS converter detected May 7 08:53:54 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB0 May 7 08:53:54 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB1 > 7. Type in /dev/ttyUSB1 in your J-Pilot preference tab under serial > port and click OK. > Did it. > 8. Re-load J-Pilot and cancel Hotsynch on the Treo (from step 6 above). > Press hotsynch on the Treo, wait 2 seconds, press hotsynch on J-Pilot. > You should here the device beep and start to synchronize. > I get no beep, but sometimes it beeps; can't figure out what sequence produces it. > 9. If this doesn't work, let us know what happened and we will try to > trouble shoot. If this works, send money to Judd Montgomery. > Sorry, no money yet. I get: May 7 08:58:50 AL-WS kernel: usb 1-2: USB disconnect, address 107 May 7 08:58:50 AL-WS kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0 May 7 08:58:50 AL-WS kernel: visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1 May 7 08:58:50 AL-WS kernel: visor 1-2:1.0: device disconnected May 7 08:58:51 AL-WS kernel: usb 1-2: new full speed USB device using ohci_hcd and address 108 May 7 08:58:51 AL-WS kernel: usb 1-2: new device found, idVendor=0830, idProduct=0061 May 7 08:58:51 AL-WS kernel: usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=5 May 7 08:58:51 AL-WS kernel: usb 1-2: Product: Palm Handheld May 7 08:58:51 AL-WS kernel: usb 1-2: Manufacturer: Palm, Inc. May 7 08:58:51 AL-WS kernel: usb 1-2: SerialNumber: PalmSN12345678 May 7 08:58:51 AL-WS kernel: usb 1-2: configuration #1 chosen from 1 choice May 7 08:58:51 AL-WS kernel: visor 1-2:1.0: Handspring Visor / Palm OS converter detected May 7 08:58:51 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB0 May 7 08:58:51 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB1 May 7 09:01:03 AL-WS kernel: hub 1-0:1.0: port 2 disabled by hub (EMI?), re-enabling... May 7 09:01:03 AL-WS kernel: usb 1-2: USB disconnect, address 108 May 7 09:01:03 AL-WS kernel: visor 1-2:1.0: device disconnected May 7 09:01:03 AL-WS kernel: usb 1-2: new full speed USB device using ohci_hcd and address 109 May 7 09:01:03 AL-WS kernel: usb 1-2: device descriptor read/64, error -62 May 7 09:01:04 AL-WS kernel: usb 1-2: new full speed USB device using ohci_hcd and address 110 May 7 09:01:04 AL-WS kernel: usb 1-2: new device found, idVendor=0830, idProduct=0061 May 7 09:01:04 AL-WS kernel: usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=5 May 7 09:01:04 AL-WS kernel: usb 1-2: Product: Palm Handheld May 7 09:01:04 AL-WS kernel: usb 1-2: Manufacturer: Palm, Inc. May 7 09:01:04 AL-WS kernel: usb 1-2: SerialNumber: PalmSN12345678 May 7 09:01:04 AL-WS kernel: usb 1-2: configuration #1 chosen from 1 choice May 7 09:01:04 AL-WS kernel: visor 1-2:1.0: Handspring Visor / Palm OS converter detected May 7 09:01:04 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB2 May 7 09:01:04 AL-WS kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB3 :-/ Al
More information about the jpilot mailing list